The round at the bottom of the boss should Figure 4 - Drafting Guidelines for Nominal Wall Thickness Cross section showing draft Figure 5 - Rib design guidelines 1/4˚—–1˚ 2.5W 3W Min. .01" R Min. or .25W .75W for a low shrink material .50W for a high shrink material Figure 6 - Wall thickness changes due to rib placement 16.00 14.00 12.00 10.00 8.00 6.00 4.00 2.00 5.00 10.00 15.00 20.00 25.00 30.00 35.00 Rib-height (mm) M ax D is p la ce m en t M ag n it d e (m m ) FIGURE 4 - Drafing guidelines for nominal wall thickness FIGURE 5 - Rib design guidelines FIGURE 7 - Wall thickness changes due to rib placement FIGURE 6 - Rib height vs. stiffness 10 Gravi-Tech FIGURE 8 - Side Wall Boss Design Guidelines Sink Not Recommended Preferred Design A = Diameter = A = Primary Wall = A = 2A FIGURE 9 - Guidelines Design Guidelines 4W 2W .75W For a Low Shrink Material .50W For a High Shrink Material FIGURE 9 - Side wall boss design guidelines FIGURE 10 - Gusset design guidelines FIGURE 11 - Structural hole be 10% of wall thickness. A larger processing window will account for the lot to lot changes between materials, without having to make process changes.3 Setting the Beginning Variables • Injection Pressure = Maximum of machine - Should not be pressure limited • Injection Velocity = Maximum of machine - This is for the injection velocity curve starting point - If flashing is an issue start slower and then increase • Injection Cut-Off Time = 15 seconds - This is only a limiting factor, needs to be above 10 seconds for velocity graph • Hold Pressure = 0 - Need to get 95% full part with a hold pressure of 0 • Hold Time = 10-15 seconds - Need to ensure gate is frozen • Screw Speed = 90% of Maximum - Unless shear sensitive material, if shear sensitive, set RPMs to optimum • Cooling Time = 10–15 seconds • Shot Size = 50% of calculated part volume • Decompression = .25" • Transfer Position = High enough to ensure a cushion - Cushion size does not matter but there must be a cushion to keep a constant pressure on the melt during hold time - Typically 0.25" is sufficient • Back Pressure = 800-1000 plastic pressure - 100–150 hydraulic pressure - Unless specified by material data sheet Determining Shot Size The shot size should be determined by calculating the combined volume of the parts and the runner system. If the material is shear-sensitive, consult the material data sheet or processing guide for instructions to set recovery time • The cooling time should only be 1–2 seconds longer than the screw recovery time, unless dictated by dimensional stability or part thickness Minimize Clamp Pressure This step is done to reduce the amount of energy used by the machine

Avient 2011, 2018 and 2021 multiples reflect trailing 12 months EBITDA at December 31. 28 EV / 2023E EBITDA 6.5 8.5 11.0 10.8 16.1 15.5 14.1 14.0 10.3 21.0 19.0 14.3 12.1 11.8 11.7 11.5 9.7 11 21 23 PM AV FM Avient Historic Multiple Avient Specialty Other Specialty / AP P E N DI X 30 Performance Additives 16% Pigments 12% TiO2 Dyestuffs 2% Polyethylene Nylon Polypropylene Styrenic Block Copolymer Other Raw Materials 33% ~40% hydrocarbon based (Grey shaded materials are hydrocarbon based, includes portion of “Other Raw Materials”) Non-hydrocarbon based materials 2022 pro forma results for the acquisition of Avient Protective Materials RAW MATERIAL BASKET SEGMENT DATA U.S. & Canada 40% 37% 18% 2022 PRO FORMA SEGMENT, END MARKET AND GEOGRAPHY GEOGRAPHY REVENUESEGMENT FINANCIALS Building and END MARKET REVENUE $2,355M $402M $1,300M $272M Sales EBITDA Specialty Engineered Materials Color Additives and Inks $592M$3,653M (1) 9% 32 (1) Total company sales and adjusted EBITDA of $3,653M and $592M, respectively, include intercompany sales eliminations and corporate costs 2022 REVENUE | $2 .4 BILLION US & Canada 34% 38% END MARKET REGION 33 34% 21% Building & 1% Energy 2% COLOR, ADDITIVES & INKS 2022 PRO FORMA REVENUE | $1 .3 BILLION US & Canada 52% 35% 34 19% 8%Industrial 16% 9% Defense Building & END MARKET REGION SPECIALTY ENGINEERED MATERIALS 32% 27% 14% Building & 3% 1% Defense 1% (18% of sales) 9% 2022 PROFORMA AVIENT REGIONAL SALES 27% 14% 17% Building & (37% of sales)Transportation 12% Building & US & Canada (40% of sales) 7% 56% 23% 7% Building & 1% LATAM (5% of sales) 3% 35 BY END MARKET Reconciliation of Non-GAAP Financial Measures (Unaudited) (Dollars in millions, except for per share data) Senior management uses comparisons of adjusted net income from continuing operations attributable to Avient shareholders and diluted adjusted earnings per share (EPS) from continuing operations attributable to Avient shareholders, excluding special items, to assess performance and facilitate comparability of results.

 Addressable market exceeds $40 billion St f d t t th t t t d ti Strong performance demonstrates that our strategy and execution are working  Megatrends and emerging opportunities align with our strengths  Innovation and services provide differentiation, incremental pricing power, and competitive advantage  Strong and proven management team driving growth and performance The New PolyOne: A Specialty Growth Company g p g g g p PolyOne Corporation Page 21 The New PolyOne: A Specialty Growth Company Appendix PolyOne Corporation Page 22 2Q 2016 Financial Highlights  Performance Products & Solutions operating margin grew 370 basis $18 $16 $21 $22 PP&S Operating Profit points year-over-year to 12.3% $11 $16 $10 $14 SEM O ti P fit  SEM operating margin expanded 50 basis points to a record second $19 $20 $21 $22 SEM Operating Profit Adjusted EPS quarter level of 14.9% $13 $10 $14 $0.37 $0.51 $0.57 $0.63 $0.45 $0.70 Adjusted EPS  Second quarter adjusted EPS has grown on average 20% per year PolyOne Corporation Page 23 $0.30 $ since 2012 Note: $ in millions, except per share data Color, Additives and Inks 2015 Revenues: $0.8 Billion Solutions 48% 33% 16.7% 18.0% 20%+Operating Income % of Sales Expanding Profits2015 Revenue by Industry Segment Textiles 4.6% 5.1% 5.5% 7.2% 8.1% 12.2% Building & C i PolyOne Corporation Page 24 Electrical & 1% Specialty Engineered Materials 2015 Revenues: $0.5 Billion Solutions 49%49% 29% 14.7% 14.9% 20%+Operating Income % of Sales 2015 Revenue by Industry Segment Expanding Profits 19% 1.1% 1.3% 3.4% 5.1% 9.6% 8.0% 8.6% 9.3% 12.1%Building & Electrical & PolyOne Corporation Page 25 Designed Structures and Solutions Solutions2015 Revenues: $0.5 Billion 97% 8-10% Operating Income % of Sales Expanding Profits2015 Revenue by Industry Segment Packaging 19% 1.4% 5.6% 7.3% 3.0% 1.0%Building & Construction Industrial 24% Transportation 33% PolyOne Corporation Page 26 2012 2013 2014 2015 2Q'16 2020 Appliances, Construction Performance Products and Solutions Solutions2015 Revenues: $0.7 Billion 79% CanadaCanada 5% Transportation 19% Wire & Cable 12-14% Operating Income % of Sales Expanding Profits 12.3% 2015 Revenue by Industry Segment Building & Electrical & El t i 1% % 5.5% 6.9% 3.8% 3.6% 5.5% 4.3% 6.3% 7.2% 8.3%7.7% PolyOne Corporation Page 27 Distribution Key Suppliers2015 Revenues: $1.0 Billion 24% Building & 4%Consumer 13%Healthcare Electrical & 23% 6 6% 6.5-7.5% 6 5% Operating Income % of Sales53% ROIC Expanding Profits 2.6% 3.0% 3.5% 4.0% 4.6% 5.6% 6.4% 5.9% 6.6% 6.5% 6.1% PolyOne Corporation Page 28 2006 2Q 2016 Platinum Plastics: Key to Future Sustainable Development 2 lbs Plastic = 3 lbs aluminum Requires 91% less energy to  recycle a pound of plastic versus  a pound of paper3 lbs aluminum 8 lbs steel a pound of paper 27 lbs glass 33% less material by weight  than aluminum 75% less material by weight75% less material by weight  than steel 93% less material by weight  than glass PolyOne Corporation Page 29 than glass Source: SPI: Sustainability and the Plastics Industry Application Examples PolyOne Corporation Page 30 Luxury Packaging with Gravitech Density Modified Polymers • Impart weight, sound and  metallic finish to caps andmetallic finish to caps and  closures for cosmetics and  spirits applications • Elevate quality and prestige  perceptions amongperceptions among  high‐end consumers • Eliminate time and cost  associated with secondary  operations and assembly PolyOne Corporation Page 31 p y Medical Device Housings with Chemically Resistant Engineered Polymers • Durable, long‐lasting products  stand up to the most  aggressive disinfectants • Minimize environmental stress  cracking and discolorationg • One of the broadest medically y approved polymer and  colorant portfolios PolyOne Corporation Page 32 Printed Circuit Boards with Thermally Conductive Polymers • Replaces metal by etchingReplaces metal by etching  circuit designs into thermally  conductive plastic • Maintains heat transfer and  cooling capabilities of metals • Reduces both weight and cost • Increases the lifetime and  reliability of electronic systems PolyOne Corporation Page 33 Color & Design Services • Greater control of color  development and supply chain • Work across entire design  process from concept to  commercialization • Inspire creativity in the use of    polymer materials, colors                 and effects • Innovative brand differentiation • Faster development timelines PolyOne Corporation Page 34 • Faster development timelines Outdoor Applications • Leading provider of high  performance specialty materials for the recreational and sports & p leisure industry • Well positioned across all segments  to address market needs  Metal to Polymer Conversion  Lightweighting  Thermal Management  Impact Performance PolyOne Corporation Page 35 Source: Outdoor Industry Association Fiber Colorants Solutions for clothing, apparel, footwear, automotive & sporting goods • ColorMatrix Fiber Colorant Solutions Proprietary advanced liquid color  formulations and equipment enable   greater efficiency and productivity Eliminates aqueous dyeing and its  associated wastewater treatment • Solid Color Concentrates Extrusion spun fibers colored viaExtrusion‐spun fibers colored via  solid masterbatch PolyOne Corporation Page 36 PET Bottling Technology • $1.5 billion attractive, growing market  Shelf‐life  extension Weight  reduction • Improve performance and reduce cost through light‐weighting,  d d t f t l ti Greater product  consistency l b l Enhanced product  aesthetics reduced waste, faster cycle times  and extended shelf life Recyclability and  reduced carbon  footprint aesthetics High heat • Aligned with megatrend of facing  climate and resource challenges: Color and Special Effects High heat resistance Sustainability benefits include  lower package weight and  improved recyclability of package  at end of use PolyOne Corporation Page 37 at end of use  Metal Replacement Solutions • Replaces metal in LED lighting • Extends LED durability and life  span eliminating hot spots • Greater design flexibility with  fewer parts • Weight reduction l f f d• Simplifies manufacturing and  lowers total production cost PolyOne Corporation Page 38 High-Barrier Packaging Containers • Capability to extrude up to 13 layers• Capability to extrude up to 13 layers • Strong oxygen and moisture vapor  transmission protectiontransmission protection • Can be made symmetrical or  asymmetrical to meet customizedasymmetrical to meet customized  needs of broad variety of applications • Barrier protection and superiorBarrier protection and superior  sensory properties PolyOne Corporation Page 39 1 Reconciliation of Non-GAAP Financial Measures (Unaudited) (Dollars in millions, except per share data) Below is a reconciliation of non-GAAP financial measures to the most directly comparable measures calculated and presented in accordance with U.S.

Buyer acknowledges that Seller has furnished to Buyer Material Safety Data sheets, which include warnings together with safety and health information concerning the Product and/or the containers for such Product. 10. Exceto em caso de força maior, se não satisfeito com a determinação do Vendedor, o Comprador como único recurso terá o direito de rescindir este contrato sem qualquer outra obrigação mediante: (i) notificação escrita com antecedência de 10 dias; e (ii) pagamento de todos os Produtos recebidos até aquela data. 13.

https://doi.org/10.1002/pen.25815 https://doi.org/10.1002/pen.25815

No. 1, Qihang Industry Park, Haoxiang Road, Shajing Town, Baoan, Shenzhen, Guangdong, China 518104 has been found to conform to the Quality Management System standard: GB/T 19001-2016 / ISO 9001:2015 This certificate is valid for the following scope: Development and Manufacture of Masterbatch, Pigment Concentration, Plastisol; Manufacture of Plastic Compounding Material http://www.dnv.com/assurance 证书制作地点及日期: 证书认可签发机构: 上海, 2024年10月 10日 DNV - Business Assurance 中国上海市长宁区虹桥路1591号9号楼A座 邮编: 200336 电话: +86 21 32799000 朱海明 管理代表 未履行认证协议中规定条款会导致此证书失效，获证组织必须定期接受监督审核并经审核合格此证书方继续有效。 获得认可的单位: DNV Business Assurance B.V., Zwolseweg 1, 2994 LB, Barendrecht, Netherlands - TEL: +31(0)102922689. www.dnv.com/assurance 本证书信息可在国家认证认可监督管理委员会官方网站（WWW.CNCA.GOV.CN） 上查询 管理体系认证证书 证书号码: 3033-2006-AQ-RGC-RvA 首次签发日期: 2018年11月 07日 有效期限: 2024年11月 08日 – 2027年11月 07日 兹证明 普立万聚合体（深圳）有限公司 中国广东省深圳市宝安区沙井镇蚝乡路启航工业园1号 518104 统一社会信用代码：9144030076498189X0 质量管理体系符合 : GB/T 19001-2016 / ISO 9001:2015标准 此证书对下列范围有效: 色母粒，色浆，增塑溶胶的开发和制造；塑料改性材料的制造 http://www.dnv.com/assurance WWW.CNCA.GOV.CN）上查询

Once a specific resin has been identified for your needs, you can check in the table whether Avient has already masterbatches listed for the corresponding supplier and under which conditions of use (minimum thickness, exact rating and maximum let-down ratio).

Buyer acknowledges that information in Seller’s marketing materials, technical data sheets and other descriptive publications distributed or published on its websites may vary from time to time without notice. Buyer acknowledges that Seller has furnished to Buyer Safety Data Sheets, which include warnings together with safety and health information concerning the Product and/or the containers for such Product. Buyer acknowledges and represents that it is familiar with and shall strictly comply with all applicable laws and regulations concerning the trade, export or re-export of products, services, data or technology (“Items”), including the International Traffic in Arms Regulations (ITAR), the Export Administration Regulations (EAR) and the trade sanctions regulations administered by the U.S.

Buyer acknowledges that information in Seller’s marketing materials, technical data sheets and other descriptive publications distributed or published on its websites may vary from time to time without notice. Buyer acknowledges that Seller has furnished to Buyer Safety Data Sheets, which include warnings together with safety and health information concerning the Product and/or the containers for such Product. Buyer acknowledges and represents that it is familiar with and shall strictly comply with all applicable laws and regulations concerning the trade, export or re-export of products, services, data or technology (“Items”), including the International Traffic in Arms Regulations (ITAR), the Export Administration Regulations (EAR) and the trade sanctions regulations administered by the U.S.

Buyer acknowledges that information in Seller’s marketing materials, technical data sheets and other descriptive publications distributed or published on its websites may vary from time to time without notice. Buyer acknowledges that Seller has furnished to Buyer Safety Data Sheets, which include warnings together with safety and health information concerning the Product and/or the containers for such Product. Buyer acknowledges and represents that it is familiar with and shall strictly comply with all applicable laws and regulations concerning the trade, export or re- export of products, services, data or technology (“Items”), including the International Traffic in Arms Regulations (ITAR), the Export Administration Regulations (EAR) and the trade sanctions regulations administered by the U.S.