Pune, India 4. Pune, India 4. It sets the objectives for the Company, and holds management accountable for achieving our strategy.

Big or small, we earn customers, and we keep them. From technology portfolios to end markets to geographies and distribution channels, this acquisition made perfect sense. Whether an additional line at an existing manufacturing plant, or a new facility in a growing region, we ramp-up quickly and cost-efficiently. 17 Capex / Revenue 2021E (%) AVIENT IS ASSET LIGHT Avient Specialty Other 2 3 2 2 3 3 3 3 4 5 5 5 5 5 6 6 7 7 9 t (E x c l.

BASE RESIN PPA PC PSU PES PPS CO- POLYMER ACETAL PEEK PA Barrel Temperatures* °F (°C) Rear Zone 550–580 (288–305) 520–560 (271–293) 600–640 (316–338) 630–660 (332–338) 550–580 (288–304) 350–370 (177–188) 660–700 (349–371) 440–490 (227–254) Center Zone 560–600 (293–316) 530–570 (277–299) 620–670 (327–354) 650–680 (343–360) 560–615 (293–324) 380–390 (193–200) 700–730 (371–388) 470–510 (243–266) Front Zone 580–620 (304–327) 550–580 (288–305) 630–680 (332–360) 670–730 (354–388) 590–630 (310–332) 390–430 (200–221) 720–750 (382–400) 490–540 (254–282) Nozzle 575–615 (302–324) 550–600 (288–316) 630–680 (332–360) 680–700 (360–371) 600–625 (316–330) 380–415 (193–213) 720–750 (382–400) 520–570 (271–300) Melt Temperature 575–615 (302–324) 560–600 (293–316) 625–675 (330–358) 650–710 (343–377) 600–625 (316–330) 370–410 (188–210) 670–740 (354–393) 520–570 (271–300) Mold Temperature 250–300 (121–150) 175–240 (80–116) 190–300 (88–150) 225–325 (107–164) 250–325 (121–164) 150–225 (66–107) 290–375 (143–190) 150–200 (66–93) Pack & Hold Pressure 50%–75% of Injection Pressure Injection Velocity in/s 1.0–3.0 Back Pressure psi 50 Screw Speed rpm 50–90 Drying Parameters °F (°C) 6 hrs @ 175 (80) 4 hrs @ 250 (121) 4 hrs @ 275 (135) 4 hrs @ 300 (150) 4 hrs @ 250 (121) 2 hrs @ 200 (93) 3 hrs @ 300 (150) 4 hrs @ 180 (82) Allowable Moisture % < 0.05 < 0.02 < 0.02 < 0.04 < 0.02 0.15–0.20 < 0.02 0.10–0.20 Cushion in 0.125–0.250 Screw Compression Ratio 2.5:1–3.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General General General General General General General Reverse Taper Clamp Pressure 5–6 Tons/in2 of projected area of cavities and runner system * Barrel temperatures should be elevated for compounds designed for electrical insulative properties. PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Increase shot size • Increase injection rate • Increase packing pressure Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature TROUBLESHOOTING RECOMMENDATIONS Note: These are general processing conditions.

Caps, Closures & Containers: Thermoplastic elastomers play a big role in the design of ergonomically enhanced packages that can help aging users accomplish simple tasks such as opening a bottle of aspirin or a jar of coffee.

Caps, Closures & Containers: Thermoplastic elastomers play a big role in the design of ergonomically enhanced packages that can help aging users accomplish simple tasks such as opening a bottle of aspirin or a jar of coffee.

So whether you’re looking for the next big thing in fiber coloration, an automated dispensing solution for your printing inks or an anti-slip vinyl backing for your carpet application, speak to our experts to find the solution that works for you.

Caps, Closures & Containers: Thermoplastic elastomers play a big role in the design of ergonomically enhanced packages that can help aging users accomplish simple tasks such as opening a bottle of aspirin or a jar of coffee.

Base Resin PPA PC PSU PES PPS Co- polymer Acetal PEEK PA Barrel Temperatures* °F (°C) Rear Zone 550–580 (288–305) 550–590 (288–310) 600–640 (316–338) 630–660 (332–338) 550–580 (288–304) 350–370 (177–188) 660–700 (349–371) 440–490 (227–254) Center Zone 560–600 (293–316) 570–600 (300–316) 620–670 (327–354) 650–680 (343–360) 560–615 (293–324) 380–390 (193–200) 700–730 (371–388) 470–510 (243–266) Front Zone 580–620 (304–327) 580–630 (304–322) 630–680 (332–360) 670–730 (354–388) 590–630 (310–332) 390–430 (200–221) 720–750 (382–400) 490–540 (254–282) Nozzle 575–615 (302–324) 580–630 (304–322) 630–680 (332–360) 680–700 (360–371) 600–625 (316–330) 380–415 (193–213) 720–750 (382–400) 520–570 (271–300) Melt Temperature 575–615 (302–324) 580–625 (304–330) 625–675 (330–358) 650–710 (343–377) 600–625 (316–330) 370–410 (188–210) 670–740 (354–393) 520–570 (271–300) Mold Temperature 250–300 (121–150) 175–240 (80–116) 190–300 (88–150) 225–325 (107–164) 250–325 (121–164) 190–250 (88–121) 290–375 (143–190) 150–200 (66–93) Pack & Hold Pressure 50%–75% of Injection Pressure Injection Velocity in/s 1.0–3.0 Back Pressure psi 50 Screw Speed rpm 50–90 Drying Parameters °F (°C) 6 hrs @ 175 (80) 4 hrs @ 250 (121) 4 hrs @ 275 (135) 4 hrs @ 250 (121) 3 hrs @ 300 (150) 2 hrs @ 200 (93) 3 hrs @ 275 (135) 4 hrs @ 180 (82) Cushion in 0.125–0.250 Screw Compression Ratio 2.5:1–3.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General General General General General General General Reverse Taper Clamp Pressure 5–6 Tons/in2 of projected area of cavities and runner system * Barrel temperatures should be elevated for compounds designed for electrical insulative properties. PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Increase shot size • Increase injection rate • Increase packing pressure Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS www.avient.com Copyright © 2020, Avient Corporation.

BUILDING & CONSTRUCTION INDUSTRY BULLETIN SAFETY Security and prevention SOLUTION: Flame retardants, laser marking additives, electrical and thermal additives SURFACE FINISH Low maintenance, natural wood grain aesthetics SOLUTION: Wood plastic composite (WPC) capstock technology PROTECTION Potable water tanks, electrical connectors, piping & tubing, insulation SOLUTION: Antimicrobials, electrical and thermal additives LONGEVITY Long service life, chemical resistance, mold & mildew resistance SOLUTION: Weatherable colorants, impact modifiers, antimicrobial additives SUSTAINABILITY LEED building & material credits, healthy building, reduced energy use, lightweighting, eco-conscious SOLUTION: Recycled materials, chemical foaming agents, bio-derived colorants & additives LANDSCAPE HARMONY Concrete surfaces, patio coloring, stucco SOLUTION: Pool colorants, metallic flooring colorants, stains The building and construction industry is dynamic, with trends towards high- performance buildings, elegant outdoor areas, healthier living spaces, and eco-friendly environments. DESIGN & PROCESSING Material flexibility and customization, extrusion and molding optimization techniques SOLUTION: Advanced polymer science, application development, technical service VISUAL AESTHETICS Custom colors, deep shades, special effects SOLUTION: Metallic colorants, granite & woodgrain effects DURABILITY Wind & impact resistance, chemical resistance, weatherability SOLUTION: Scratch & mar resistant or IR/UV resistant additives, dimensional stabilizers TECHNOLOGY DESCRIPTION TYPICAL APPLICATIONS Antimicrobial Antimicrobial technology to limit microbe growth— reduces bacterial, mold and fungal growth on surface and through thickness, protecting finished part • Potable water equipment • Roofs & eaves • Decking, fencing & railings • High-touch surfaces • Bath surrounds, liners & inserts Scratch & Mar Resistance For applications requiring resistance to daily surface abrasion, and management of surface energy • Exterior fencing, decking, railings & shutters • Outdoor furniture • Playground equipment Flame Retardant Reduces spread of fire and heat release by creating a char to limit oxygen at the flame source • Wire & cable • Telecommunications • Decking, fencing & railings • Conduit • Exterior siding & cladding • Housings UV and Light Blocking UV stabilizers help mitigate the harmful effects of UV radiation while light blocking additives protect products sensitive to light • Exterior siding & cladding • Trim & moldings • Roofing, shingles, tiles • Outdoor furniture • Fencing, decking, railings & shutters Anti-static and Conductive Controls build-up of static charges to create static-dissipated parts while reducing related dust accumulation • Electrical connectors • Conduit or tubing • Junction boxes • Flooring • 5G enabling Chemical Foaming Agents Reduces weight and density without compromising mechanical properties • Exterior siding & cladding • Modular panels • Decking, fencing & railings Optimization Additives Cycle-time reducers that help optimize production while allowing improved dimensional stability and energy efficiency, among other processing benefits • Used in extrusion and injection molding processes to improve thermal conductivity, and lower processing temperatures and energy consumption Laser Marking Supports design and production flexibility and offers a new level of control in marking polymers with speed and clarity • Wire & cable • Outdoor furniture • Equipment & housings • Pipes & fittings Anti-counterfeiting Customizable in-plastic authentication technologies that enable positive identification versus counterfeit products • Wire & cable jacketing • Pipes & fittings • Telecommunications • Potable water equipment Wood Plastic Composite (WPC) Capstock Technology Pair with traditional WPC materials as a substrate for a durable outer layer • Exterior siding & cladding • Outdoor furniture • Fencing, decking & railings Sustainable Colorants & Color concentrates and additives carefully chosen to meet industry requirements and legislation, and designed to lower environmental impact while improving sustainability • Green building roofing • OSHA compliance • Sheet & profile extrusions • LEED building & material credits FX Special Effects Colorants Granite, marbling, woodgrain and other distinctive colorant technologies to provide special surface effects • Decorative molding • Chair or hand rails • Wallcovering • Blinds & shutters • Any surface or part demanding a distinctive look Pool Colorants Durable, long-lasting pigment formulations for finishes that hold up to pool water chemistries • Pool decks • Coping • In-ground swimming pools Metallic Flooring & Stain Colorants Colorants designed to give concrete floors and surfaces a distinctive appearance • Concrete flooring • Countertops • Decorative concrete • Walls While this listing represents many Avient solutions and addresses common applications, we can tackle many other building & construction needs.

Employing Excelite additives can help achieve density reductions, smoother surface finish, linear consistency and a tighter cell structure. The technology is highly suitable for printable sheet, where smooth surface finish and low density is a requirement. EXCELITE VS POWDER • Enables a greater level of density control, through consistent distribution in the polymer • Simplifies and optimizes resin compounding capabilities (PVC dry blends) • Enables greater control over foaming and expands processing window when re-introducing regrind • Clean and highly accurate dosing process, with fewer of the health and safety concerns that can become apparent with powder CFAs EXCELITE VS PELLET • Being significantly more concentrated, Excelite additive enables lower total cost to foam • Can achieve lower density, less carrier influence • Finer and tighter cell structure through better additive distribution • Improved linear consistency of cell structure as ColorMatrix pumps continually meter output, giving greater stability over material dosing • Improved plant working capital as lower let down ratios means less material is consumed and reduces inventory holdings TECHNICAL SUPPORT • Avient has a market leading service team which understands foaming processes, we assist customers to deliver performance and production efficiencies with Excelite™ technology • Please contact your local Avient representative for additional information on our line of foaming additives www.avient.com Copyright © 2020, Avient Corporation.