Er kunnen situaties zijn waarin het vermijden van faciliterende betalingen of smeergeld de persoonlijke veiligheid van onze medewerkers (of hun families) in gevaar kan brengen.

Sink Marks Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase shot size • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Burning • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Warp • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Processing Guide 7 Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

For the latest information about developments related to Form W-9 and its instructions, such as legislation enacted after they were published, go to www.irs.gov/FormW9. Note: Entering “Applied For” means that you have already applied for a TIN or that you intend to apply for one soon.

Ces relations sont importantes pour Avient et fournissent des contributions précieuses dans de nombreux domaines d’activité. Savoir que l’interdiction s’applique qu’un article bénéficie ou non directement à l’individu ou à une autre personne, comme à un membre de sa famille, à un ami ou un collaborateur • Tenir des livres, registres et comptes de manière raisonnablement détaillée, et refléter avec précision et équité la transaction • Effectuer une diligence raisonnable sur les agents, distributeurs et autres tiers avant l’engagement et pendant la relation, et obtenir l’approbation du service juridique • Gérer et contrôler correctement les activités commerciales menées par l’intermédiaire de tiers À NE PAS FAIRE • Offrir, promettre, payer ou autoriser le paiement de toute chose de valeur à tout représentant officiel public ou employé du secteur privé pour aider Avient à obtenir ou à conserver un marché, ou à obtenir tout autre avantage commercial illicite.

If Seller grants a discount, such discount only relates to the delivery and/or quantity of the Products specifically mentioned in Seller’s order confirmation. Any such statement, sample or other information of Seller in relation to the Specifications, the Products and the use thereof are furnished for the accommodation of Buyer only and are not warranties or representations of performance. 14. The Tokyo District Court shall be the court with exclusive jurisdiction for the first instance over any lawsuit and other legal proceedings arising from or relating to these Terms. 21.

Subject to the foregoing, and except as otherwise expressly provided herein, Seller makes no representation or warranty of any kind with respect to the Product, express or implied, relating to merchantability or fitness for any particular purpose. DATA PROTECTION Buyer hereby agrees that any data in relation with the business relationship between Buyer and Seller may be processed by Seller, in compliance with applicable laws and regulations. 15.

The failure mode is dual meaning both adhesive and cohesive on these substrates.

L’acheteur remboursera au vendeur toutes les taxes fédérales, de l’État, locales ou autres taxes (autres que l’impôt sur le revenu), taxes d’accise ou charges, y compris la taxe et les frais destinés au Superfund, que le vendeur doit payer en relation avec la fabrication et la fourniture de produits en vertu des présentes, mais seulement dans la mesure où elles ne sont pas déjà incluses dans le prix précisé aux présentes. 8.

Solutions also sold as Renol™ UL 94 Colorants IMPORTANCE OF UL 94 There are two major established norms in the E&E industry that relate to plastics flammability: the IEC 60695 standard and the UL 94 standard.

Related Products and Services