KEY PERFORMANCE PROPERTIES1 PHYSICAL NOMINAL VALUE UNIT TEST METHOD Density/Specific Gravity 1.00 ASTM D792 Melt Mass-Flow Rate (MFR) (230°C/2.16kg) 20 g/10 min ASTM D1238 MECHANICAL Tensile Strength 15.0 MPa ASTM D638 Flexural Modulus 1400 MPa ASTM D790 Flexural Strength 35.0 MPa ASTM D790 IMPACT Notched Izod Impact (Injection Molded) 150 J/m ASTM D256 ELECTRICAL Surface Resistivity < 100000 ohms/sq ASTM D257 PROCESSING INFORMATION INJECTION NOMINAL VALUE UNIT Drying Temperature 80 to 90 °C Drying Time 4.0 to 6.0 hr Processing (Melt) Temperature 220 to 250 °C Mold Temperature 30 to 80 °C Trilliant™ HC Electrically Conductive Formulations for Precision Performance Pipette Tips A critical design consideration for pipette tips is the accurate measurement of finite amounts of liquid.

TECHNICAL BULLETIN Characteristics Artisan™ Nylon Solution Painted Metal Painted Plastic Traditional Molded-in Color Impact Modified Nylon PA Ionomer Alloy Aesthetic Very Good Excellent Excellent Good Very Good Very Good Scratch Appearance Excellent Poor Poor Good Excellent Excellent Scratch & Mar Resistance Very Good Excellent Excellent Poor Very Good Excellent Color Customization Good Excellent Excellent Very Good Good Good Stress Whitening Excellent Fair Fair Poor Excellent Excellent Weatherability Good Excellent Excellent Very Good Good Very Good Temperature Performance Good Excellent Fair Fair Fair Good Corrosion Resistance Excellent Fair Excellent Excellent Excellent Excellent Processability One Step Multi Step Multi Step One Step One Step Complex One Step Total Production Cost $$$ $$$$$ $$$$ $$ $$$ $$$$ Order Quantity Restrictions Some Some Some None More More COMPARISON OF NYLON, METAL, AND PLASTIC Properties Test Method Artisan™ AR6000-0007 HI UV* Gloss Level** Gloss reading at 60 degrees 80-93 Molding Shrinkage – Across Flow ASTM D955 0.009 to 0.013 in/in Tensile Strength (Yield) ASTM D638 7300 psi Tensile Strength (Break) ASTM D638 5300 psi Tensile Elongation (Yield) ASTM D638 6.0% Flexural Modulus ASTM D790 270500 psi Flexural Strength (Yield) ASTM D790 9950 psi Notched Izod Impact ASTM D256 -4°F (-20°C) 5 ft-lb/in 73°F (23°C) 11 ft-lb/in Unnotched Izod Impact ASTM D256 -4°F (-20°C) 29 ft-lb/in 73°F (23°C) 30 ft-lb/in Color & Aesthetics*** Green, medium blue, dark blue, red, orange, white, gray, black Color customization available based on specific needs KEY PROPERTIES Features: high-gloss finish, UV stability, scratch resistance, chemical/corrosion resistance, cold temperature impact resistance, heat resistance * Reflects average of several colors, properties shift slightly depending on color ** Gloss level varies based on tooling temperature *** UV data available upon request Copyright © 2023, Avient Corporation.

OnColor™ UL 94 Colorants* • More than 2,000 recognized concentrates available worldwide in all color options • HB rating for most of PP, PS, ABS, PC/ABS, PBT, PA, PA-GF, TPU generic resins • V-0, V-1, V-2 and 5VA/5VB ratings for more than 200 specific engineering resins • Master file of recognized concentrates with scope of use accessible in the UL product finder • Development of custom products for specific resins upon request • Compliance Letters available for REACH and RoHS Cesa™ Flame Retardant Additives for Glow Wire • Fire performance in line with different levels of Glow Wire temperatures (IEC 60695-2-12) • Let-Down Ratio adjustable to reach different levels of Glow Wire temperatures • Non-halogen (in accordance with IEC 61249- 2-21) and non-HBCD** solutions • Wide range of solutions adapted to different polymers (PP, PS, PC) • Color and flame retardants can be combined in one product • Compliance Letters available for REACH and RoHS APPLICATION BULLETIN * Solutions also sold as Renol™ UL 94 Colorants APPLICATION POLYMER GWFI TEMPERATURE TYPICAL LET-DOWN RATIO CONTENT HIPS 750–960°C 5–10% Non-HBCD flame retardant** PC 850–960°C 2–4% Non-halogen in accordance with IEC 61249-2-21 PP homopolymer 850–960°C 4% Non-halogen in accordance with IEC 61249-2-21 PP copolymer 850–960°C 4–8% Antioxidant - metal deactivator ** Non-HBCD means that Hexabromocyclododecane (HBCD) is neither used as starting material during the mixing phase of our products nor intentionally added during production, but it cannot be excluded that it is not present at level of ubiquitous traces in any of the raw materials used in manufacturing of our products.

Microsoft PowerPoint - AVNT Q4 2023 Earnings Presentation v7 AVIENT CORPORATION F O U R T H Q U A R T E R 2 0 2 3 R E S U L T S A N D 2 0 2 4 F I N A N C I A L G U I D A N C E (NYSE: AVNT) F E B R U A R Y 1 4 , 2 0 2 4 D I S C L A I M E R Forward-Looking Statements Certain statements contained in or incorporated by reference into this presentation constitute “forward-looking statements” within the meaning of the Private Securities Litigation Reform Act of 1995. ASHISH KHANDPUR P R E S I D E N T & C E O 4 5 PORTFOLIO TRANSFORMATION 5 7% 46% 66% 87% 100% 0% 20% 40% 60% 80% 100% 2005 2010 2015 2020 2023 % o f A dj us te d E B IT D A Commodity JVs Distribution Performance Products & Solutions Specialty Businesses Adjusted EBITDA from Specialty Applications SUSTAINABILITY AS A GROWTH DRIVER 7 LONG-TERM REVENUE GROWTH DRIVERS Sustainable Solutions Composites, Healthcare, Asia / LATAM Overlap Other 60%+ Key Growth Drivers Total Company Revenue Growth Drivers Long-Term Growth Rate Sustainable Solutions 8–12% Composites 8–10% Healthcare 8–10% Asia / LATAM 5% Other 0–2% Avient 6% END MARKET OBSERVATIONS ( % O F C O M PA N Y S A L E S ) ENERGY 5% DEFENSE 7% TELECOMMUNICATIONS 4% HEALTHCARE 7% 8 TRANSPORTATION 10% INDUSTRIAL 16% BUILDING & CONSTRUCTION 9% CONSUMER 19% PACKAGING 23% 9 REGIONAL OBSERVATIONS ( % O F C O M PA N Y S A L E S ) 9 US & Canada Latin America EMEA Asia 41% 36% 18% 5% Q 4 2 0 2 3 R E S U L T S Q4 2023 PERFORMANCE VS. GUIDANCE ( T O TA L C O M PA N Y ) 11 $710 $719 Guidance Actual $112 $114 Guidance Actual Sales Adjusted EBITDA (in millions) $0.47 $0.52 Guidance Actual Adjusted EPS (in millions) 13.5% 15.9% 2022 2023 Results vs.

DOCUMENT NUMBER_ SSS-001 CATEGORY DETAIL EC Number 215-609-9 CAS Number 1333-86-4 Name Subclass 1 Carbon Black Structural Formula CHEMICAL IDENTITY H | C||||HH H DOCUMENT NUMBER_ SSS-001 HEALTH EFFECTS HUMAN HEALTH SAFETY ASSESSMENT Consumer Overall, as a result of the detailed epidemiological investigations, no causative link between Carbon Black exposure and cancer risk in humans has been demonstrated. Toxicity for Reproduction PROPERTY DETAIL Physical State Solid Form Powder/ Beads Color Black Odor Odorless Melting Point 3550°C Boiling Point 500–600°C Partition Coefficient: N-octanol/Water Not Applicable Bulk Density 1.7-1.8 g/cm3 (20°C) Water Solubility Insoluble Self-ignition Temperature >284°F Flammability >45 s Explosiveness 50 g/m3 PHYSICAL/CHEMICAL PROPERTIES DOCUMENT NUMBER_ SSS-001 EXPOSURE HUMAN HEALTH SAFETY ASSESSMENT Human Health Carbon Black, when generally used as noted above is bound into a matrix.

Vectran® is thermotropic and melts at 330°C. Key Features • High strength to weight ratio • Good creep resistance • High abrasion resistance • Excellent flex fatigue properties • Minimal moisture absorption • Excellent chemical resistance Disadvantages • Vectran® suffers from UV degradation, which causes strength loss and discoloration • Hair-like filaments tend to fray FIBER-LINE® PROCESS FOR VECTRAN® LIQUID CRYSTAL POLYMER • Coating • Twisting • Extrusion • Pultrusion • Precision Winding FIBER-LINE® VECTRAN® PRODUCTS • Strength Members • Ripcords • Belt & Hose Reinforcement Yarn • Industrial Fabric Yarn • Synthetic Wire Rope Abrasion Resistance Yarn on Yarn Abrasion Ultraviolet (UV) Resistance Flame Resistance Chemical Resistance (Acid) Chemical Resistance (Alkali) Chemical Resistance (Organic Solvent) P P X P P P P Property UOM Value Breaking Tenacity g/d 23.0 Specific Gravity Ratio 1.40 Elongation @ Break % 3.8 Tensile Modulus g/d 600 Moisture Regain* % LIQUID CRYSTAL POLYMER (LCP) LIQUID CRYSTAL POLYMER (HM) BARE FIBER PERFORMANCE * Equilibrium moisture regain @ 55% RH ** Creep @ 40%-58% ultimate tensile strength *** Shrinkage in dry air @ 177 C for 30 minutes MOVING HIGH PERFORMANCE FIBERS FORWARD ABOUT FIBER-LINE® LOCATIONS Headquarters, R&D, Manufacturing FIBER-LINE® LLC 3050 Campus Drive Hatfield, PA 19440 +1 215.997.9181 fiber@fiber-line.com Manufacturing Operations FIBER-LINE® LLC 280 Performance Drive SE Hickory, NC 28602 +1 828.326.8700 fiber@fiber-line.com EMEA & Asia Pacific Operations FIBER-LINE® INTERNATIONAL B.V.

The coarse ground material was then crystallized in a vacuum oven at 160°C before drying the material at 160°C for approx. 4 hours within a PET drier • Plaques were then molded on a BOY XS and 10 of these were kept after each cycle, to take color measurements • This process was then repeated until 5 heat cycles had been completed RESULTS FOR RECYCLABILITY METHOD-1 As plaques were produced while the material went through five different melt heat histories, plaques were produced at each cycle and L*, a*, and b* values were measured. Key: A = 4% Amosorb SolO2-2 + Fortis Amber-1 @ 0.09%; B = 50% Regrind A + 50% Virgin PET; C = 50% Regrind A + 50% Virgin PET + Fortis Amber @ 0.045% REGRIND COMBINATION STUDY - METHODOLOGY 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation. It was also demonstrated that usage of a reduced amount of color, namely 0,045% of Fortis Amber-1, allows the production of bottles (Bottle C) that closely resembles the original bottles (Bottle A).

Peel, PLI 12 19 23 20 19 reSound OM 5510 for PP reSound OM 5510-60N Room Temperature 70C 1 day 1 week 2 weeks 6 months 1 week 2 weeks 3 weeks Bio-derived Content (%) 50% 50% 50% 50% 50% 50% 50% Hardness, Shore A 60 60 60 60 60 60 60 Specific Gravity 0.89 0.89 0.89 0.89 0.89 0.89 0.90 50% Modulus, PSI 247 241 244 251 234 244 240 100% Modulus, PSI 343 333 338 339 321 331 326 Tensile Strength, PSI 625 621 647 610 633 662 642 Elongation, % 306 314 309 313 312 315 315 Tear Strength, PLI 109 108 113 113 111 117 115 reSound OM 5520-55N Room Temperature 70C 1 day 1 week 2 weeks 6 months 1 week 2 weeks 3 weeks Bio-derived Content (%) 49% 49% 49% 49% 49% 49% 49% Hardness, Shore A 54 54 55 55 54 55 56 Specific Gravity 0.95 0.95 0.96 0.96 0.95 0.96 0.96 50% Modulus, PSI 258 256 256 265 266 271 257 100% Modulus, PSI 353 355 357 362 373 379 367 Tensile strength, PSI 637 615 637 669 651 674 642 Elongation, % 319 315 319 333 313 319 315 Tear Strength, PLI 146 136 133 142 137 138 141 reSound OM 5510-45N Room Temperature 70C 1 day 1 week 2 weeks 6 months 1 week 2 weeks 3 weeks Bio-derived Content (%) 40% 40% 40% 40% 40% 40% 40% Hardness, Shore A 45 46 47 46 46 45 45 Specific Gravity 0.88 0.89 0.89 0.89 0.89 0.89 0.90 50% Modulus, PSI 153 158 154 162 137 136 133 100% Modulus, PSI 251 259 259 261 226 222 218 Tensile Strength, PSI 438 481 451 495 417 470 486 Elongation, % 215 240 211 243 204 227 238 Tear Strength, PLI 84 81 87 82 83 85 84 AGING – PROPERTY RETENTION • Tested at room temperature and 70° C for comparison • Hardness, tensile strength elongation and modulus showed great retention Overmolding onto PP Overmolding onto ABS RHEOLOGY Suitable for injection molding and overmolding 1.0 10 100 1000 10000 100000 10.0 100.0 1000.0 reSound OM 5510-30N reSound OM 5510-45N reSound OM 5510-60N reSound OM 5510-70N Shear Rate, 1/s C ap ill ar y Vi sc os it y, P a* s 1.0 10 100 1000 10000 100000 10.0 100.0 1000.0 reSound OM 5520-55N Shear Rate, 1/s C ap ill ar y Vi sc os it y, P a* s Capillary viscosity at 200°C Capillary viscosity at 200°C reSound OM 5510 for PP reSound OM 5520 for ABS www.avient.com Copyright © 2020, Avient Corporation.

INDUSTRY BULLETIN STANDARD UNITS ONFLEX LO 7120-45N Volatile Organic Compounds VDA 278 ug/g(ppm) 41 Fogging VDA 278 ug/g(ppm) 521 Odor • Control • Dry conditions • Wet conditions SAE J1351 (15) 1-10 Scale 1 2 1 Compression Set (23°C) • 22 hours • 70 hours ASTM D395 % 14.4 14.6 Capillary Viscosity • 1341/s • 11170/s ASTM D3835 Pa*s 35 7 HVAC SYSTEMS OnFlex™ LO • Features: low VOC/FOG, low odor, good compression set, easy processing, overmolds to polypropylene • Example applications: seals and flaps in heating, ventilation and air conditioning systems CHARACTERISTICS ONFLEX ™ LO ONFLEX™ AF TPE GENERAL PURPOSE TPV TPO Volatile Organic Compounds (VDA 278) Very Low Moderate Moderate Moderate Very Low Fogging (VDA 278 & DIN 75201) Very Low Moderate Moderate High Very Low Odor (VDA 270 Requirement ≤3.0) ≤3.0 ≤3.0 >3 >3 ≤3.0 Gloss Level Low Low Low Very Low High Tactile Feel Grippy Grippy Grippy Grippy Waxy Pre-Drying Required No No No Yes No Raw Material Costs $$ $$ $$ $$$ $ Compression Set @ RT Good Good Good Excellent N/A Compression Set @ ≥70°C Moderate Moderate Moderate Good N/A UV Resistance Good Excellent Good Good Good Weatherability Good Excellent Good Good Good Hardness Range Low to High Low to High Low to High Low to High High Density (g/ml) 1.15 0.99 0.90–1.20 0.95–0.98 0.90–1.20 GENERAL CHARACTERISTICS COMPARING TPE, TPV, TPO Grades shown on both pages are representative of solutions manufactured in North America, more grades available globally. INTERIORS/EXTERIORS TEMP STANDARD UNITS ONFLEX AF 7210-40B ONFLEX AF 7210-50B ONFLEX AF 7210-60B ONFLEX AF 7210-70B ONFLEX AF 7210-80B QUV Exposure • 1000 Hrs(0.68 W/m2 @ 340nm) • 2000 Hrs(0.68 W/m2 @ 340nm) 45°C ΔE 0.49 0.38 0.42 0.48 0.21 0.85 0.22 0.14 0.32 0.24 Xenon-Arc Exposure • 1000 Hrs(0.35 W/m2 @ 340nm) 63°C ΔE 0.63 0.84 0.34 — 0.58 Capillary Viscosity • 1341/s • 11170/s ASTM D3835 Pa*s 60 11.4 79 15 65 13 48 13.7 73 16 Ozone Resistance ASTM D1149(16) B Visual No cracks No cracks No cracks No cracks No cracks Low Temperature Brittleness ISO 812 B °C -63 -62 -62 -62 -62 OnFlex™ AF • Features: long-term sealing performance, reduced noise and vibration, grippy feel, low gloss, low odor, excellent UV resistance and weatherability, easy processability, overmolds to polypropylene • Example applications: trays, door pockets, fasteners, clips, roof rack pads, roof and door trim, and window encapsulations The need to innovate is virtually endless.

Handelsregister B des Amtsgerichts Mannheim Nummer der Firma: Seite 1 von 4 HRB 521568 Nummer der Eintragung a) Firma b) Sitz, Niederlassung, inländische Geschäftsanschrift, empfangsberechtigte Person, Zweigniederlassungen c) Gegenstand des Unternehmens Grund- oder Stammkapital a) Allgemeine Vertretungsregelung b) Vorstand, Leitungsorgan, geschäftsführende Direktoren, persönlich haftende Gesellschafter, Geschäftsführer, Vertretungsberechtigte und besondere Vertretungsbefugnis Prokura a) Rechtsform, Beginn, Satzung oder Gesellschaftsvertrag b) Sonstige Rechtsverhältnisse a) Tag der Eintragung b) Bemerkungen 1 2 3 4 5 6 7 1 a) PolyOne Th. Bergmann GmbH b) Gaggenau c) Die Herstellung, Verarbeitung, Vertrieb sowie Handel von Kunststoffen oder Kunststoffcompounds aller Art. a) 02.02.2017 Rinke 9 b) Berichtigung von Amts wegen zur Geschäftsanschrift: Adolf-Dambach-Str. 2, 76571 Gaggenau a) 06.06.2018 Rinke 10 b) Bestellt als Geschäftsführer: a) 25.03.2019 Rinke Abruf vom 08.11.2021 19:52 Handelsregister B des Amtsgerichts Mannheim Nummer der Firma: Seite 4 von 4 HRB 521568 Nummer der Eintragung a) Firma b) Sitz, Niederlassung, inländische Geschäftsanschrift, empfangsberechtigte Person, Zweigniederlassungen c) Gegenstand des Unternehmens Grund- oder Stammkapital a) Allgemeine Vertretungsregelung b) Vorstand, Leitungsorgan, geschäftsführende Direktoren, persönlich haftende Gesellschafter, Geschäftsführer, Vertretungsberechtigte und besondere Vertretungsbefugnis Prokura a) Rechtsform, Beginn, Satzung oder Gesellschaftsvertrag b) Sonstige Rechtsverhältnisse a) Tag der Eintragung b) Bemerkungen 1 2 3 4 5 6 7 Potoczny, Zaneta Gabriela, Mersch / Luxemburg, *17.10.1974 mit der Befugnis, im Namen der Gesellschaft mit sich im eigenen Namen oder als Vertreter eines Dritten Rechtsgeschäfte abzuschließen.