TEMPERATURE Material Rear Center Front Nozzle Melt Mold Nylon 6,6 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) Nylon 6,6 30% SS 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) PBT 510–410 (265–280) 490–540 (255–280) 480–530 480–530 480–530 150–250 (65–120) PC 14% NiCF 540–570 540–570 530–560 530–560 530–560 150–250 (65–120) ABS 470–520 460–520 460–520 460–530 (240–275) 460–530 (240–275) 100–200 (40–90) PP 440–480 (225–250) 440–480 (225–250) 430–470 (220–245) 420–460 (215–240) 420–460 (215–240) 125–175 (50–80) DRYING Material Temperature °F (°C) Time Minimum Moisture Maximum Moisture Nylon 6,6 14% NiCF 180 (80) 4–5 hours 0.05% 0.20% Nylon 6,6 30% SS 180 (80) 4–5 hours 0.05% 0.20% PBT 14% NiCF 250 (120) 6-8 hours 0.02% 0.03% PC 14% NiCF 250 (120) 3–4 hours 0.02% 0.02% ABS 14% NiCF 200 (90) 2–4 hours 0.05% 0.10% PP 14% NiCF 180 (80) 2–4 hours 0.20% 0.30% Equipment • Feed throats smaller than 2.5" may cause bridging due to pellet size - Larger feed throats will be more advantageous with long fiber EMI shielding resins • General purpose metering screw is recommended - Mixing/barrier screws are not recommended • L/D ratio - 18:1–20:1 (40% feed, 40% transition, 20% metering) • Low compression ratio - 2:1–3:1 • Deep flights recommended - Metering zone 3.5 mm - Feed zone 7.5 mm • Check ring - Three-piece, free-flowing check ring • General purpose nozzle (large nozzle tips are recommended) - Minimum orifice diameter of 7/32" - Tapered nozzles are not recommended for long fiber EMI shielding resins • Clamp tonnage: - 2.5–5 tons/in2 Gates • Large, free-flow gating recommended - 0.25" x 0.125" land length - 0.5" gate depth Runners • Full round gate design • No sharp corners • Minimum of 0.25" diameter • Hot runners can be used PROCESSING Screw Speed Slower screw speeds are recommended to protect fiber length Back Pressure Lower back pressure is recommended to protect fiber length Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) PROCESS CONSIDERATIONS Recommended – retain fiber length (maximize conductivity) • Low shear process • Low screw speed and screw RPM • Slow Injection speed • Fill to 99–100% on first stage of injection - Reduces potential nesting of fibers at gate location - Improves mechanical performance near gate location - Promotes ideal fiber orientation Resin Rich Surface • Achieved when using a hot mold temperature and longer cure times ≥ Max mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could reduce attenuation performance in an assembly Fiber Rich Surface • Achieved when using a cold mold temperature and shorter cure times ≤ Minimum mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could improve attenuation performance in an assembly www.avient.com Copyright © 2020, Avient Corporation.

A TechTalk Presentation on April 17 from 15:00 to 15:20 hours at Stand R31 in Hall 16 on sustainable bio-based materials, including zero-carbon emission TPEs, low-warpage and low-water absorption nylons, ‘OK-compost’ certified biopolymer solutions and successful case studies A Design Forum on April 19 from 10:35 to 11:00 hours at Hall 18, Room CC201A, 2/F, on ColorForward™ Color Forecasting and GraviTech™ Density-Modified Formulations

A LOOK INTO THE FUTURE VIRTUAL REALITY APPLICATION BULLETIN AESTHETIC APPEAL Metallic and Custom Effects, FDA-Approved Masterbatch Colorants SOLUTION: Custom Polymer Colorants, Pre-Colored Resins WEARABLE COMFORT Flexibility, Skin- Compatible Comfort, Soft Touch, Heat Reduction SOLUTION: Thermoplastic Elastomers (TPEs), Thermoplastic Urethanes (TPUs), Silicone, Nylon (PA) FUNCTIONALITY Impact Resistance, Dimensional Stability, Strength SOLUTION: Copolyester, PC/ Polyester Blends, Polycarbonate, Styrenics BETTER EXPERIENCES. DURABILITY Impact Strength, Rigid or Flexible Materials SOLUTION: Thermoplastic Elastomers (TPEs), Thermoplastic Urethanes (TPUs), Copolyester, Polycarbonate, PC Blends, PMMA, Styrenics, Nylon (PA), Silicone SURFACE PROTECTION Performance Enhancing Additives SOLUTION: Antimicrobial Additives, Scratch and Mar Additives ERGONOMICS Soft Touch, Easy to Grip SOLUTION: Thermoplastic Elastomers (TPEs), Thermoplastic Urethanes (TPUs), Silicone TOUGHNESS Impact Strength, Chemical Resistance SOLUTION: PC/Polyester Blends, Copolyester WEAR PERFORMANCE Wear-Resistance SOLUTION: Polyester (PET), Nylon (PA), Acetal (POM) DISCOVER.

DURABILITY High Impact Strength, Weatherability SOLUTION: PP, HDPE, ASA, Nylon Engineered Formulations AESTHETIC APPEAL Custom Color & Special Effects, Paint Replacement SOLUTION: Custom Polymer Colorants, Pre-Colored High-Gloss Thermoplastics THERMAL MANAGEMENT LED Heat Sinks, Design Flexibility SOLUTION: Thermally Conductive Formulations EXTREME PERFORMANCE Chemical & Fire Resistance, High Temperature Performance SOLUTION: Nylon Engineered Formulations, Long Fiber Reinforced Composites, Continuous Fiber Composite Tapes & Laminates, Flame Retardant Polyolefin Formulations STRUCTURAL INTEGRITY High Stiffness-to-Weight Ratio, Metal Replacement SOLUTION: Pultruded Rods, Tubes & Custom Profiles, Long Fiber Reinforced Composites SENSORY EXPERIENCE Vibration Damping, Durability, Customization, Custom Color, Low Friction SOLUTION: Thermoplastic Elastomers (TPEs), Custom Polymer Colorants, Internally Lubricated Formulations, Advanced Composite Springs STRENGTH & STABILITY Excellent Dimensional Stability, High Stiffness, Impact Resistance SOLUTION: Short & Long Fiber Formulations, Continuous Fiber Composite Tapes & Laminates SURFACE PROTECTION Performance Enhancements SOLUTION: Scratch & Mar Resistance, UV Stable Additives, Anti-Static Additives STRUCTURAL PERFORMANCE Corrosion Resistance, Lightweighting SOLUTION: Long Fiber Reinforced Composites, Nylon Engineered Formulations, Continuous Fiber Composite Tapes & Laminates, Chemical Foaming Additives METAL REPLACEMENT Lightweighting, Heat Management, Load Carrying Capability SOLUTION: Long Fiber Reinforced Composites, Continuous Fiber Composite Tapes & Laminates TACTILE EXPERIENCE Soft-Touch Feel, Durability SOLUTION: Thermoplastic Elastomers (TPEs) A COLLABORATION THAT BRINGS STYLE & GRIT To all thrill seekers, fans and enthusiasts, your brand says, “Bring it!”

Q1 2023 (TOTAL COMPANY) $846 $829 $134 $143 17.3% (in millions) $0.63 $0.76 Adjusted EPS (in millions) + 7% + 21% Sales Adjusted EBITDA Adjusted EPS 6 - 2% 15.8% +150 bps Q1 2024 SEGMENT PERFORMANCE (COLORS, ADDITIVES & INKS) $537 $515 $91 $97 18.8% (in millions) (in millions) + 7% 7 - 4% 17.0% +180 bps • Year over year demand continues to improve for the segment but slowly due to continued weakness in Europe • Raw material deflation & cost reduction actions primary drivers of adjusted EBITDA growth and margin expansion of +180 bps vs Q1 2023 Q1 2024 SEGMENT PERFORMANCE (SPECIALTY ENGINEERED MATERIALS) $310 $314 $64 $73 23.2% (in millions) (in millions) + 14% 8 + 1% 20.8% +240 bps • Sales growth in defense end market offset by weaker demand in telecommunications end market • Raw material deflation and favorable mix impact from defense sales primary drivers of adjusted EBITDA growth and margin expansion of +240 bps vs Q1 2023 Q1 EBITDA BRIDGE (TOTAL COMPANY) 9 $ millions CAI: Price / Mix (1) Deflation 16 SEM: Price / Mix 4 Deflation 7 Net Price Benefit 26 Wage/Other Inflation (9) FX (2) Q1 2024 $143 Adjusted EBITDA Q1 2023 $ 134 Demand (6) • Positive net price benefit: o Favorable raw material deflation in both segments • Wage and other inflation more than offset cost reductions/synergies 2024 G U I DAN CE FY 2024 GUIDANCE Original Revised Adjusted EBITDA $505 to $535 million $510 to $535 million Adjusted EPS $2.40 to $2.65 $2.50 to $2.65 Interest Expense $105 to $110 million $105 million Adjusted Effective Tax Rate 23% to 25% 23% to 25% Capital Expenditures ~$140 million ~$140 million 11 Q2 2024: Adjusted EPS of $0.71 CE O “ TO P O F MI N D” FO CU S ARE AS AREAS OF FOCUS 13 +7% Drive Profitable Organic Top-Line Growth with Margin Expansion Amplify Innovation Build Leadership & Talent Pipeline AP P E N DI X 16 Performance Additives 15% Pigments TiO2 Dyestuffs Polyethylene 10%Nylon Polypropylene Styrenic Block Copolymer Other Raw Materials 38% ~40% hydrocarbon based (Grey shaded materials are hydrocarbon based, includes portion of “Other Raw Materials”) Non-hydrocarbon based materials RAW MATERIAL BASKET SEGMENT DATA U.S. & Canada 41% 36% 2023 SEGMENT, END MARKET AND GEOGRAPHY GEOGRAPHY REVENUESEGMENT FINANCIALS 19% 23%Industrial Building and 7% END MARKET REVENUE $2,007M $358M $1,138M $224M Sales EBITDA Specialty Engineered Materials Color Additives and Inks $502M$3,143M (1) 7% 18 (1) Total company sales and adjusted EBITDA of $3,143M and $502M, respectively, include intercompany sales eliminations and corporate costs 2023 REVENUE | $2 .0 BILLION 34% 37% 21% END MARKET REGION 19 34% 21% 15% Building & 1% Energy COLOR, ADDITIVES & INKS 2023 REVENUE | $1 .1 BILLION 52% 35% 20 6%Industrial 12% 10% Defense Building & END MARKET REGION SPECIALTY ENGINEERED MATERIALS 32% 26% Building & 6% 2% Defense 1% (18% of sales) 2023 AVIENT REGIONAL SALES 25% Building & (36% of sales)Transportation 22% Building & 12% 6% US & Canada (41% of sales) 59% 22% Building & LATAM (5% of sales) 21 BY END MARKET Reconciliation of Non-GAAP Financial Measures (Unaudited) (Dollars in millions, except for per share data) Senior management uses comparisons of adjusted net income from continuing operations attributable to Avient shareholders and diluted adjusted earnings per share (EPS) from continuing operations attributable to Avient shareholders, excluding special items, to assess performance and facilitate comparability of results. A reconciliation of these measures to their most directly comparable GAAP measures is provided in the tables below. 2024 2023 Reconciliation to Condensed Consolidated Statements of Income $ EPS $ EPS Net income from continuing operations attributable to Avient shareholders $ 49.4 $ 0.54 $ 20.8 $ 0.23 Special items, after-tax 5.5 0.06 22.3 0.24 Amortization expense, after-tax 14.9 0.16 15.1 0.16 Adjusted net income / EPS $ 69.8 $ 0.76 $ 58.2 $ 0.63 Three Months Ended Reconciliation to EBITDA and Adjusted EBITDA: 2024 2023 Net income from continuing operations – GAAP $ 49.7 $ 21.3 Income tax expense 16.8 7.7 Interest expense, net 26.6 28.8 Depreciation and amortization 44.3 50.5 EBITDA from continuing operations 137.4 108.3 Special items, before tax 6.2 27.3 Depreciation and amortization included in special items (0.5) (1.8) Adjusted EBITDA $ 143.1 $ 133.8 Adjusted EBITDA as a percent of sales 17.3 % 15.8 % 1 2024 2023 Sales: Color, Additives and Inks $ 515.3 $ 537.0 Specialty Engineered Materials 314.4 309.7 Corporate (0.7) (1.0) Sales $ 829.0 $ 845.7 Operating income: Color, Additives and Inks $ 74.8 $ 65.6 Specialty Engineered Materials 53.4 43.1 Corporate (34.2) (51.6) Operating income $ 94.0 $ 57.1 Depreciation & amortization: Color, Additives and Inks $ 21.9 $ 25.8 Specialty Engineered Materials 19.6 21.2 Corporate 2.8 3.5 Depreciation & amortization $ 44.3 $ 50.5 Earnings before interest, taxes, depreciation and amortization (EBITDA): Color, Additives and Inks $ 96.7 $ 91.4 Specialty Engineered Materials 73.0 64.3 Corporate (31.4) (48.1) Other (expense) income, net (0.9) 0.7 EBITDA from continuing operations 137.4 108.3 Special items, before tax 6.2 27.3 Depreciation and amortization included in special items (0.5) (1.8) Adjusted EBITDA $ 143.1 $ 133.8 Adjusted EBITDA as a percent of sales: Color, Additives and Inks 18.8 % 17.0 % Specialty Engineered Materials 23.2 % 20.8 % 2 Year Ended December 31, 2023 Sales: Color, Additives and Inks $ 2,007.4 Specialty Engineered Materials 1,138.2 Corporate (2.8) Sales $ 3,142.8 Operating income: Color, Additives and Inks $ 259.9 Specialty Engineered Materials 142.5 Corporate (205.6) Operating income $ 196.8 Depreciation & amortization: Color, Additives and Inks $ 98.3 Specialty Engineered Materials 81.5 Corporate 9.0 Depreciation & amortization $ 188.8 Earnings before interest, taxes, depreciation and amortization (EBITDA): Color, Additives and Inks $ 358.2 Specialty Engineered Materials 224.0 Corporate (196.6) Other income, net 5.8 EBITDA from continuing operations 391.4 Special items, before tax 114.6 Interest expense included in special items (2.3) Depreciation and amortization included in special items (1.9) Adjusted EBITDA $ 501.8 3 AVNT Q1 2024 Earnings Presentation_For_Website_w_non-GAAP.pdf Avient corporation�first quarter 2024 results and 2024 financial guidance DISCLAIMER Slide Number 3 Regional demand trends-total company�Q1 Sales vs PY (Excluding FX) Slide Number 5 Slide Number 6 Slide Number 7 Slide Number 8 Slide Number 9 Slide Number 10 Slide Number 11 Slide Number 12 Slide Number 13 Slide Number 14 Slide Number 15 Slide Number 16 Slide Number 17 2023 segment, end market and Geography Color, Additives & Inks Specialty Engineered Materials Slide Number 21 IR Deck - AVNT-2024.03.31 5.06 11AM v2 (002).pdf Attachment

As an alternative to metal and metal inserts, high-density plastic materials with customizable specific gravity, which can range from 1.5 to 11, can be used for weighting and balancing. The team selected a long glass fiber-reinforced nylon material (Complēt™ PA66-LGF50 composite) for the shaft substrate to provide strength and to withstand hammering impact. Epoxy and nylon plugs were used for the ends.