This growth means new challenges for materials and technologies to ensure these state-of-the-art charging stations meet critical standards and performance specifications. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Seller is entitled to deliver the Products as stated in the order confirmation in partial shipments and to invoice accordingly. With respect to the state of Ohio, this waiver applies to Section 35 Article II of the Ohio Constitution and Ohio Revised Code Sec. 4123.74. 16. The law of the State of Ohio shall apply, without regard to conflict of law principles.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information. CAUSE AND EFFECT DIAGRAM Methods Machines Materials Manpower energy saving during SBM Maintenance instructions Operating instructions Operator Job spec NIR Lamps SBM Type/Design vPET reheat content vPET formulation rPET blend/quality Temperature recording Temperature measurement probe External temperature Inappropriate Manual Training New Alignment Same Throughput Too many tasks Time conflict Age/intensity variable Set up conditions Configuration - When starting to process a new resin, first run through new preforms for 15 minutes at ‘standard’ conditions to establish steady state conditions prior to any process optimization - Slowly start to reduce preform blowing temperatures until failures are present (visible pearl internal wall or pearl feet) - Increase blowing temperatures until defects are eliminated - QC check bottle quality for acceptance versus established tolerances - Change the power consumption profile in the ovens for early heat and longer sink times but ensure overall temperatures do not exceed cold crystallization temperature - Repeat temperature reduction stage and then defect elimination stage to test if further optimization is possible - Recheck QC bottle quality for acceptance versus established tolerances - Log all process parameters and create new specific ‘recipe’ for future use

HOW ALTERNATIVE POLYMERS COMPARE TO PA 6,6 PA 6 | POSSIBLE APPLICATIONS: Automotive, Industrial, Consumer & Sporting Goods Wider processing temperature range Better surface quality Better weathering resistance Shorter conditioning time—nearly half that of PA 6,6 Lower temperature resistance Slightly lower chemical resistance Higher water absorption Lower stiffness/wear resistance PK | POSSIBLE APPLICATIONS: Automotive, Consumer & Sporting Goods, Industrial, Electrical & Electronics Lower CO2 emissions in production Better hydrolysis and chemical resistance Comparable dimensional stability Inherently lubricious for reduced wear and friction Easier to mold Cost competitive Lower short- and long-term thermal performance Harder to color More limited process window PBT/PET | POSSIBLE APPLICATIONS: Electrical & Electronics Lower water absorption Slightly higher rigidity/stiffness (for PBT) Better abrasion resistance Slightly better electric resistance Lower toughness properties Higher density Lower short- and long-term temperature resistance Lower hydrolysis resistance PP | POSSIBLE APPLICATIONS: Automotive, Consumer Goods, Lightweighting Applications Lower water absorption Slightly better chemical resistance Lower density Cost effective Fiber reinforced PP can achieve similar or better mechanical properties to PA 6,6 GF30 Reduced rigidity/stiffness Much lower abrasion resistance Lower electric resistance Reduced short- and long-term temperature resistance PC/PBT & PC/PET BLENDS | POSSIBLE APPLICATIONS: Automotive Interiors, Consumer Goods, Household Appliances Higher impact strength Good scratch resistance Good wear resistance Lower mechanical properties Higher brittleness Narrow processing temperature range PA 6,6/PET BLENDS | POSSIBLE APPLICATIONS: Automotive, Industrial, Appliance, Electrical & Electronics, Applications Where Low Water Absorption is Required Reduced water absorption—up to 40% Slightly higher mechanical properties in the conditioned state Slightly lower temperature resistance Slightly lower chemical resistance Narrow processing temperature range PA/PP BLENDS | POSSIBLE APPLICATIONS: Automotive Interiors, Electronics, Consumer & Sporting Goods Good adhesion to polyolefin-based TPEs Low permeability of water Good processability Lower density Lower temperature resistance Lower mechanical properties POST-INDUSTRIAL RECYCLED SOLUTIONS (PA 6,6/PA 6/PP) | POSSIBLE APPLICATIONS: Automotive Accessories, Industrial, Consumer & Sporting Goods Between 50-80% recycled content Good processability Cost effective Reduced chemical resistance Wider range of mechanical specifications Potential for slightly lower mechanical properties 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Recycle Loop AAnchor Mg/kg Anthranilamide Mg/kg Virgin Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Values reported as intypical in or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the information.