La Porte, Indiana 30. Board of Directors Gender Female 25% Male 75% Age 30–50 17% Over 50 83% Race & Ethnicity U.S. These injection moldable TPEs can be overmolded to polypropylene (PP) and come in a natural grade that can be easily colored.

Screw Speed Low–moderate Injection Velocity 1–3 inch per second Back Pressure Low–moderate Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) Residence Time Long residence times are not advised 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

EXTRUDER Screw 3/4" to 6" Polyethylene type—Single flight, no mixing section, 1.5–2:1 compression ratio Tooling Semi-Pressure type: 30°–40° angle Die On size with 1/8" or less land L/D 24:1 recommended Screen Pack No screen pack (Optional depending on pressure) Cooling Trough 120–150°F (50–65°C) recommended Feeder Gravimetric type preferred—3 compartment for cross-linked Dryer Desiccant type, 4 hours at 160°F (70°C) For ECCOH™ compound only; never put Dry Silane in Dryers PROCESSING Temperature ECCOH 5000 Series ECCOH 6000 Series Wire Preheat 180–250°F (80–120°C) 180–250°F (80–120°C) Feed Zones 200°F (93°C) 275°F (135°C) Transition 275°F (135°C) 325°F (163°C) Metering 300°F (150°C) 375°F (190°C) Head/Die 330°F (165°C) 420°F (215°C) Target Melt 330–340°F (165–170°C) 420–440°F (215–225°C) Flame at Die Tip Yes—as needed Line Speed Shear sensitive: Observe Melt Temperature, Motor Amperage, and Pressure Purge Compound HDPE Copyright © 2020, Avient Corporation.

Based on industry averages, a leather armrest typically adds $30 to the cost of producing a single door, while the approximate cost of a slush molded vinyl armrest is about $10 per door.

In 2014, it was spun off from Closure Systems International (CSI), and currently produces over three billion aluminum closures annually in 28 and 30 millimeter diameters suitable for any type of still, carbonated or alcoholic beverage packaged in glass, PET or aluminum bottles.

KEY CHARACTERISTICS • Excellent wear resistance • Reduced friction, heat build-up, noise and vibration • Improved processability and surface finish on parts • Lower power requirements and low maintenance • Design flexibility • Reduced weight APPLICATION BULLETIN SOLUTIONS AVAILABLE LubriOne™ Portfolio PA66, PA6 and Polyketone formulations with 10%–30% glass fiber reinforcement available Lubricants & Performance Lubricant Color Performance LubriOne NN PTFE Natural Shears and creates a PTFE film transferred to the matting surface.

COLORANT CHROMATICS HIGH-TEMPERATURE POLYMER FORMULATIONS PRODUCT SELECTION GUIDE COLORANT CHROMATICS HIGH TEMPERATURE COMPOUNDS PROPERTY ISO Test Method Units PES PPSU PEI LCP PEEK PSU PHYSICAL Density 1183 — 1.37 1.29 1.27 1.40 1.30 1.24 Mold Shrinkage Flow/X-flow 294–4 % 0.8/0.85 0.7/XX 0.6/0.7 0/0.7 1.0/1.3 0.7 MECHANICAL Tensile Strength 527 Mpa 85 70 85 200 100 70 Tensile Elongation Yield 527 % 7 7.5 6 — — 6 Tensile Elongation Break 527 % >25 >60 60 3 30 >50 Izod Notched 180 kJ/m2 7 55 5 95 7 5.5 THERMAL HDT 1.8 MPa 75 °C 205 200 190 190 150 175 FLAMMABILITY Flame Rating UL-94 — V-0 V-0 V-0 V-0 V-0 HB ADDITIONAL Steam Sterilizable — Cycles 100 2000 2000 1500 1000 100 CUSTOM OPTIONS Color — — Yes Yes Yes Yes Yes Yes Reinforced — — Yes Yes Yes Yes Yes Yes Conductive — — Yes Yes Yes Yes Yes Yes Lubricated — — Yes Yes Yes No Yes Yes Radiopaque — — Yes Yes Yes No Yes Yes Trade Names — — Veradel Ultrason E Radel Ultrason P Ultem Vectra Zenite Xydar KetaSpire Victrex Vestakeep Udel Ultrason S Avient high temperature precolored and specialty compounds are your solutions for high performance products.

In addition, the profit margin on this product was about 30% higher than that of other models.

The Chamber of Commerce recommends that this document be viewed in digital form so that its integrity is safeguarded and the signature remains verifiable. 20 21 -0 4- 12 1 4: 06 :2 8 under number CHE-112.279.714 Sole shareholder since 20-10-2015 (registration date: 03-11-2015) Board members Name Borst, Rainer Erich Date of birth 10-10-1961 Date of entry into office 01-07-2020 (registration date: 06-07-2020) Title Director Powers Solely/independently authorised Name Kamalak, Ihsan Date of birth 21-08-1985 Date of entry into office 01-07-2020 (registration date: 06-07-2020) Title Director Powers Solely/independently authorised Name Merklein, Norbert Date of birth 03-05-1964 Date of entry into office 05-03-2021 (registration date: 30-03-2021) Powers Solely/independently authorised Extract was made on 12-04-2021 at 14.06 hours.

Performance Products & Solutions (PP&S) achieved a new record for return on sales at 7.2 percent and further reduced its working capital as a percent of sales to 4.3 percent. This strength was most notably evidenced by our hiring last year of Brad Richardson as CFO and Michael Garratt as president of PP&S. On May 30, 2013, the Company divested these two facilities, and the business they support to Mexichem.