Increase injection rate 4. Increase gate size to allow higher flow rate and lower molded in stress Wet material 1. Increase injection rate 3.

Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time Processing Guide 5 Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase pack pressure/time Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size Melt and/or mold too hot • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease injection speed • Decrease screw rpm • Increase venting Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase injection speed • Increase screw rpm • Decrease cooling time 6 Therma-Tech Burning Melt and/or mold too cold Mold design • Clean, widen and increase number of vents • Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase vent width and locations Mold design • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure Mold design • Increase draft angle Part is too hot 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

Outdoor High Performance) 8 18% 3 Growth in Asia / LATAM 6 3% 2 Other 100 19% 5 Sub-total $1,327 14% $146 Outdoor High Performance Impact (5) (3) Wage Inflation and Overtime (11) Other Supply Chain Costs (4) Synergies 5 Incentives, Other Employee Costs 8 FX (28) (5) Q1 2022 $1,294 11% $136 Q1 2022 SALES AND OPERATING INCOME Sales Growth Rate Operating Income$ millions EBITDA Q1 EBITDA BRIDGE 12 Price increases more than offset raw material and supply chain impacts Q1 2021 $ 161 Demand (23) $ millions CAI: Price / Mix 77 Inflation (54) SEM: Price / Mix 41 Inflation (26) Distribution: Price / Mix 84 Inflation (82) Net Price Benefit 40 Wage Inflation and Overtime (11) Other Supply Chain Costs (4) Synergies 5 Incentives, Other Employee Costs 8 FX (5) Q1 2022 $ 171 China Lockdowns / Russia Impact $ (7) Transportation (7) Outdoor High Performance (3) Q1 EPS BRIDGE 13 Q1 2021 - Adjusted EPS 0.89$ CAI 0.08 Specialty Engineered Materials 0.06 Distribution 0.00 Corporate Costs 0.02 F/X (0.04) Segment OI 0.12 Tax Rate (0.02) Q1 2022 - Adjusted EPS 0.99$ 2022 O U T LO O K REVENUE GROWTH DRIVERS Growth Drivers Long-Term Growth Rate 2022E Growth Rate Sustainable Solutions 8–12% 12% Healthcare 8–10% 10% Composites 10% 5% Asia / LATAM 5% 5% Other (GDP growth) 2–3% 2–3% Avient 6.5% 6% 15 Excluding Outdoor High Performance 20% (8% excl. Avient reflects 2022 estimated revenue of $5,100M and estimated CAPEX of $90M (excludes IT system upgrade of $15M and synergy capture CAPEX of $10M) Avient PF reflects 2022 modelled revenue of $3,740 and estimated CAPEX of $120M to reflect Dyneema run-rate CAPEX, as well as potential sale of Distribution. Free cash flow conversion calculated as (EBITDA – Capex) / EBITDA HIGH FREE CASH FLOW CONVERSION Avient reflects 2022 estimated EBITDA of $635M and estimated CAPEX of $90M (excludes IT system upgrade of $15M and synergy capture CAPEX of $10M) Avient PF reflects 2022 modelled EBITDA of $660M and estimated CAPEX of $120M to reflect Dyneema run-rate CAPEX, as well as potential sale of Distribution.

© 2019, All Right Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012 TRANSPORTATION LIGHTING SUPPLIER H E A T S I N K F O R H I G H P O W E R L E D • A material to replace aluminum • High thermal conductivity - 20 W/mK • Electrically conductive • Increase production rate by 50%, as three secondary operations were eliminated • Reduced the weight of each part by 30% • Collaborated with the customer to participate in the SPE Automotive Innovation Awards Therma-Tech™ TT6600-5001 EC Grey KEY REQUIREMENTS WHY AVIENT?

BOS B A T T E R Y S F R A M E • Recycled materials where possible • Non-halogen flame retardant performance to V0 rating • BOS company color RAL9004 (on visible parts) • Thermal performance for some parts • High strength at low thickness for load-bearing parts • Provided multiple polymer solutions for the battery frame including recycled nylon, thermoplastic elastomers and thermally conductive formulations • Utilized recycled nylon with up to 35% glass fiber content to provide high strength for load-bearing parts at a low thickness to minimize weight • Enabled customer to launch a new innovative battery system with a modular design for use in multiple applications – maximizing the working life of the battery Nymax™ REC Recycled Nylon Formulations and Therma-Tech™ Thermally Conductive Formulations KEY REQUIREMENTS WHY AVIENT?

GLOBAL SMALL APPLIANCE BRAND V A C U U M C L E A N E R H A N D L E • Comply with flame retardant ratings of UL 94 V-0 at 0.8mm and GWIT 775oC / GWFI 850oC • Pass ball pressure at 75oC • Deliver stable static resistivity of E9-11 • Matched color to a specified black103 • Pass tests for battery runaway, drop at 1m, static load, and fatigue life • Provided a custom formulation with a good balance of performance and aesthetics • Guided the molder on how to properly measure the surface resistance of the part and the fixture specifications • Had excellent service with fast turnaround of samples and strong ADTS support to ensure smooth processability Stat-Tech Static Dissipative & Electrically Conductive Formulations KEY REQUIREMENTS WHY AVIENT?

PowerPoint Presentation M E D I C A L C O N N E C T O R S • Ongoing production with no change to regular set up • Excellent processing and demolding performance • Color stability during processing • Excellent chemical and impact resistance • Enabled efficient ongoing production rates without changing any processing parameters • Safeguarded color stability and transparency during processing for optimal aesthetics • Ensured regulatory requirements for biocompatible ISO109931 and FDA were met • Provided a solution effective across a range of high-temperature polymers, including PEEK, PPSU, PES, PSU, PEI, LCP, and PPS Colorant Chromatics Evoluscend non- PFAS* high-temperature polymer mold release additive KEY REQUIREMENTS WHY AVIENT AVIENT SOLUTION PRODUCTIVITY + REGULATORY LEARN MORE ELECTRICAL COMPONENT OEM (*) A non-PFAS additive manufactured without non-intentionally added (NIA) PFAS or PTFE. (*) manufactured without intentionally added PFAS and without PTFE (1) refers to sulfone products only https://www.avient.com/products/polymer-additives/processing-enhancement-additives/colorant-chromatics-evoluscend-non-pfas-high-temperature-mold-release-additive Slide Number 1

RESPIRATORY DEVICE MANUFACTURER C P A P M A C H I N E C O V E R • Good aesthetics with high COF for grip functionality • Chemically bondable to FR PC/ABS down to 1mm • NCS S 9000-N color suitable for UV laser marking to white • Good scratch and mar resistance • Good chemical resistance to detergents, alcohols and bleach • Pass VOCs & out-gassing in accordance to ISO 18562-3/2:2017 • Customized formulation to balance mar resistance, flow, and laser marking whiteness and clarity • Collaborated on tooling improvements to widen processing window and increase yield rate • Provided application development and on- site technical support to manage short shot, sink marks, burn marks and air trap Customized VersaflexTM TPEs WHY AVIENT?

INDUSTRIAL EQUIPMENT MANUFACTURER H O U S I N G F O R C R A N E C O N T R O L • High impact performance, charpy notched > 60kJ/m2 • Part assembly: tight dimensional tolerances ±0.05mm • Critical weld lines are invisible on the final part • Red RAL 3020 as branding color • Color stability during injection • Offered a nylon (PA66) formulation with high impact resistance and dimensional stability • Supported injection trials with field technical services • Developed a ready-to-use solution in RAL 3020 with excellent color stability, helping to reduce scrap rate from >50% to 4% • Enabled timely production through fast new developments and samplings • Offered additional color options Bergamid Polyamide Formulations KEY REQUIREMENTS WHY AVIENT?

Factors that could cause actual results to differ materially from those implied by these forward-looking statements include disruptions, uncertainty or volatility in the credit markets that could adversely impact the availability of credit already arranged and the availability and cost of credit in the future; the effect on foreign operations of currency fluctuations, tariffs and other political, economic and regulatory risks; the current and potential future impact of the COVID-19 pandemic on our business, results of operations, financial position or cash flows including without any limitation, any supply chain and logistics issues; our ability to achieve the strategic and other objectives relating to the acquisition of Clariant's Masterbatch business, including any expected synergies; changes in polymer consumption growth rates and laws and regulations regarding plastics in jurisdictions where we conduct business; fluctuations in raw material prices, quality and supply, and in energy prices and supply; production outages or material costs associated with scheduled or unscheduled maintenance programs; unanticipated developments that could occur with respect to contingencies such as litigation and environmental matters; an inability to achieve the anticipated financial benefit from initiatives related to acquisition and integration working capital reductions, cost reductions and employee productivity goals; our ability to pay regular quarterly cash dividends and the amounts and timing of any future dividends; information systems failures and cyberattacks; our ability to consummate and successfully integrate acquisitions; and amounts for cash and non-cash charges related to restructuring plans that may differ from original estimates, including because of timing changes associated with the underlying actions. Three Months Ended June 30, Six Months Ended June 30, Reconciliation to Consolidated Statements of Income 2021 2020 2021 2020 Sales $ 1,235.2 $ 609.1 $ 2,397.5 $ 1,320.6 Gross margin - GAAP 288.7 149.7 591.1 321.2 Special items in gross margin (Attachment 3) 12.6 (4.2) 10.4 (4.0) Adjusted gross margin $ 301.3 $ 145.5 $ 601.5 $ 317.2 Adjusted gross margin as a percent of sales 24.4 % 23.9 % 25.1 % 24.0 % Operating income - GAAP 108.1 38.0 228.5 90.8 Special items in operating income (Attachment 3) 14.2 9.0 16.6 18.7 Adjusted operating income $ 122.3 $ 47.0 $ 245.1 $ 109.5 Adjusted operating income as a percent of sales 9.9 % 7.7 % 10.2 % 8.3 % The table below reconciles pre-special income tax expense and the pre-special effective tax rate to their most comparable US GAAP figures. Three Months Ended June 30, 2021 2020 GAAP Results Special Items Adjusted Results GAAP Results Special Items Adjusted Results $ 89.8 $ 14.2 $ 104.0 $ 31.3 $ 2.4 $ 33.7 Income tax expense - GAAP (20.4) — (20.4) (7.9) — (7.9) Income tax impact of special items (Attachment 3) — (3.4) (3.4) — (0.7) (0.7) Tax adjustments (Attachment 3) — 0.9 0.9 — 0.9 0.9 Income tax (expense) benefit $ (20.4) $ (2.5) $ (22.9) $ (7.9) $ 0.2 $ (7.7) Effective Tax Rate(1) 22.7 % 22.0 % 25.1 % 22.5 % (1) Rates may not recalculate from figures presented herein due to rounding 13 Six Months Ended June 30, 2021 2020 GAAP Results Special Items Adjusted Results GAAP Results Special Items Adjusted Results $ 192.4 $ 16.6 $ 209.0 $ 76.3 $ 12.0 $ 88.3 Income tax expense - GAAP (43.3) — (43.3) (19.8) — (19.8) Income tax impact of special items (Attachment 3) — (4.3) (4.3) — (2.7) (2.7) Tax adjustments (Attachment 3) — 2.0 2.0 — 1.9 1.9 Income tax (expense) benefit $ (43.3) $ (2.3) $ (45.6) $ (19.8) $ (0.8) $ (20.6) Effective Tax Rate(1) 22.5 % 21.8 % 25.9 % 23.3 % (1) Rates may not recalculate from figures presented herein due to rounding The following pro forma adjustments are referenced by management to provide comparable business performance by incorporating the Clariant Masterbatch business in periods prior to the acquisition date (July 1, 2020).